On-Q structured wiring enclosures feature a uniform grid pattern which has different spacing than Linear’s structured wiring enclosures’ grid pattern. Linear’s M&S Systems brand DMC-10H Structured Wire Intercom Hub can be custom installed into any of the On-Q enclosures listed above by using an OpenHouse Model H200 Universal Mounting Bracket. The H200 bracket measures 6-1/2” … Continue reading Mounting DMC-10H structured wire intercom hub in On-Q Brand enclosures
READ MORE
Linear’s M&S Systems brand Model DMC-10 Structured Wire Intercom System can provide muting control to Linear’s ChannelPlus brand Model MDS-6A Music Distribution System and other systems through the Model DMC-10AWP Audio Input Wall Plate. The wall plate features a mute output jack that provides a contact closure whenever the DMC-10 intercom system is being used … Continue reading DMC-10AWP Audio input wall plate can mute MDS-6A Music Distribution System
READ MORE
Do not operate any Red Series or Platinum Series AirVac Central Vacuum power unit with all air inlets capped. The AirVac uses air flow through the power unit to help cool the motor. SEVERE DAMAGE MAY OCCUR TO THE AIRVAC POWER UNIT IF THE UNIT IS OPERATED WITHOUT PROPER AIRFLOW! PDF: TB2007-006
READ MORE
An easy solution for mounting Linear’s M&S Systems brand Model DMC-10H Structured Wire Intercom Hub inside another manufacturer’s structured wiring enclosure containing an incompatible mounting grid is to use Linear’s OpenHouse brand Model H200 Universal Mounting Bracket as an adapter. The H200 bracket measures 6-1/2”W x 10-1/4” H and has room for one or two … Continue reading H200 Mounting bracket functions as Adapter for DMC-10H Intercom Hub
READ MORESome early models of Linear’s AVP and AVR Series AirVac Central Vacuum Power Units require the use of a Utility Inlet Port Adapter The adapter (part number 227586) connects between the central vacuum hose and the power unit’s utility inlet port. This adapter is not required for newer models of the AVP and AVR series … Continue reading Central Vacuum utility inlet port adapter
READ MORETo aid in assembly of the AirVac Tool Kits, the following information will be included in future stock of the VM1200S, VM2200DS, & VM4200DS Vacuum Accessory Packages. Link to PDF: TB2006-010
READ MOREThe M&S dmc1 Music/Communication System uses plug-in Cat-5 Insulation Displacement Connectors “Quick Connectors” for interconnection between the Master unit and the Room Stations. These connectors are designed to terminate the four color-coded twisted pairs of standard Cat-5 cable. The connector can only terminate solid copper strands of Cat-5 wire that range from 22 gauge to … Continue reading Correct wire termination using cat-5 quick connectors
READ MOREThe DXS-81 battery powered cash drawer bill trap contains a built-in transmitter.The DXS-81 is concealed in a cash drawer under a stack of currency, with a single “bait” bill secured in its money clip. During a hold-up, the cashier removes the stack of currency along with the “bait” bill. When the “bait” bill is removed, … Continue reading DXS-81 Bill trap installation tips
READ MORELinear’s access control systems can use readily available, standard, low-cost, Category-5e cable for connecting remote devices (keypads, card readers, etc.) to the system’s PBUS terminals. Category-5e (Cat-5e) cable contains four unshielded twisted pairs (4-UTP) of 24 AWG solid copper wire. Each wire pair is color coded for identification. Refer to the diagram below for the … Continue reading Cat-5e cable recommended for access control systems
READ MORE
There is an error in the DMC1 Finish-out Instructions regarding the wiring of monaural satellite speakers. Figure 4 in the instructions has incorrect CAT-5 wire color call outs. Refer to the figure below for details on correctly connecting the CAT-5 cable from the DMC1 master to the Model MVC1 Monaural Volume Control and a 45-ohm … Continue reading dmc1 monaural speaker wiring
READ MORE
